Kitchen cabinet replacements need money. Remember that the kitchen is frequently a major selling factor if you want to sell the house in a few years, so those new cabinets might leave a good first impression. After choosing kitchen cabinets, you must determine how to install them: Should you do it yourself or contact a Carpentry Contractor in Singapore?
New kitchen cabinets may make cooking and home organizing much more pleasurable if you want to stay in your house.
After choosing kitchen cabinets, you must determine how to install them: Should you do it yourself or contact a Carpentry Contractor in Singapore?
How do you install kitchen cabinets (all by yourself)?
With such a large selection of styles readily available for DIY fitting, realizing your favorite kitchen cabinet ideas in your house is simple. To assist, we have put together a step-by-step tutorial on how to install kitchen cabinets. However, you should also read the instructions provided by the specific manufacturer as designs might differ.
Done with the kitchen:
It’s crucial to repair any damage to the walls or floors before you begin. Additionally, you might wish to paint the space appropriately, giving the walls and ceiling a primer layer. Cut off the kitchen’s plumbing, gas, and electricity.
Mark directives:
Mark the location of the base cabinets on the floor with painter’s tape. Next, locate the highest point on the floor using a level. Mark the cabinet height from here on the wall, then draw a line extending from it. If you are installing the cabinets before the flooring is installed, allow for the height of the flooring.
Fit supports for the installation of upper cabinets:
Place 1 by 2 or 1 by 3 furring strips into the studs beneath the line designated for the bottom of the wall cabinets to support the higher cabinets during installation. During installation, this will support the wall cabinets. Verify the degree of support.
Set up of the cabinets:
To prevent the pieces from becoming jumbled up, it is better to build cabinets one at a time. To assemble them, adhere to the manufacturer’s instructions. You’ll install the wall cabinets first, so start there.
Ordering your cabinets preassembled will also expedite the process, but be aware that this option will cost you more money and has a higher likelihood of being damaged in transit.
Putting in wall cabinets:
Our recommended approach is to repair the wall cabinets first.
Mark the locations of the studs on the back and start with a corner unit, or the far left if you don’t have one. Make pilot holes in the cabinet’s top and bottom. Do the same for each above cabinet.
Use the mounting screws to secure the first cabinet to the wall after positioning it there. Just tighten them enough to keep it in place for the time being, though.
Verify that the first cabinet is level and plumb, and if necessary, shim behind it. Verify that the first cabinet is level and plumb, and if necessary, shim behind it.
Periodically install wall cabinets:
Ensure that the second cabinet is aligned before placing it next to the first. Clamps are used to hold the cabinets together, and screws are used to attach the second cabinet in the same manner as the first, simply tightening the screws enough to keep it in place and using shims to make it plumb if necessary.
Using a countersink twist drill bit and cabinet screws, assemble the upper cabinets.
Continue in the same manner for the subsequent rows, checking as you go that the cabinet sides and corners are even and level. Use a cabinet fill strip to fill in any gaps at the end of the row.
Completely tighten the rear screws, release the clamps, and take out the support below after the entire wall cabinets are in place. As required, fix the wall’s imperfections.
First base cabinet installation:
Start assembling the base cabinets from a corner, just like you did with the wall cabinets. Drill holes in the cabinet’s stud positions after marking them with the help of the markings on the wall. Utilizing the wall’s horizontal line as a reference, position the first cabinet, making sure it is level and plumb. Shims may be required at the bottom or the back. Screw it in and only tighten it enough to keep it in place.
Periodically fit base cabinets:
The second cabinet should be positioned adjacent to the first one after drilling the same pilot holes on the rear as previously. Shim if required to maintain even faces. Simply hold the second cabinet in place by clamping the first two cabinets together.
As with the wall cabinets, join the two cabinets together. Fit the base cabinets along the wall in the same manner as before. The area where the sink will be must-have holes made for the plumbing.
If there is a gap at the end, fill it in with a filler strip before tightening all the screws and releasing the clamps.
Trim and fit doors:
To complete, trim the cabinetry and fit the doors and drawers.
Cut the toe kicks and attach them. They will typically be 4 inches (or 10 cm) broad, but you might need to cut them smaller if your floor is uneven.
If there are large gaps between the toe kicks and the floor, it is preferable to add a foundation shoe that has been shaped to match the surface.
Is DIY Kitchen cabinet installation hard?
Kitchen cabinet installation calls for moderate DIY abilities. There aren’t many tools required, and the cabinets themselves are essentially boxes that must be fastened to the wall and linked together.
Careful measurement and taking the effort to maintain things level and plumb throughout are essential to success.
Installing new cabinets in the kitchen:
At first, glance, installing new kitchen cabinets could appear simple. After all, putting those parts together can’t be that difficult. All that remains to be done is to mount them where the previous cabinets were, right?
There is a lot more to it than that. Both serious tools and serious talents may be needed for the cabinet assembly. An experienced contractor will likely spend many hours assembling the cabinets before emerging from a pile of sawdust.
Also, keep in mind that installing kitchen cabinets involves a lot of muscle and work. Simply raising the cabinets can be difficult; someone will need to hold them in place while another person fastens them to the wall. You will surely need more than one person to complete the task. Kitchen cabinet installation is often not a solo endeavor!
The cost of new kitchen cabinets sometimes prompts homeowners to attempt their installation to save money. A high-end redesign with bespoke cabinets might cost up to SGD 30K or more, and that doesn’t even include the professional carpentry work Singapore. A low-end kitchen cabinet overhaul can cost between SGD 5K-SGD 7K.
However, only people who are handy and have prior expertise installing cabinets should attempt to do the task alone. That’s because hiring a skilled contractor may be required anyhow when anything goes wrong, as it always will.
The cost of installation then increases since the contractor now has to repair any harm that may have been caused during the botched installation effort. Many homeowners have found themselves in the terrible situation of having to pay even more money than they would have had to.
Also Read:- Bathroom renovation in Singapore: Different types of packages